• Extends HDMI signals at distances of up to 300m using a single SC duplex multimode fibre optic cable
• Compatible with HDMI specifications including HDCP, 3D multi channel audio, DDC, CEC and remote control*
• Supports 3840x2160 24Hz YCbCr 4:2:2 12-bit BT.2020 / HDR10@24Hz Blu-ray UHD
• Supports all HDTV resolutions up to 1600p including 1080i, 1080p, 1440p and 4K2K
• Supports deep Colour modes with 30/36/48 bit colour depth
• 10.2Gbps Total Bandwidth over Single 2-core Fibre Optic Cable Link
• IR Frequency range 35-45kHz
• 2 year warranty

*Remote control requires our Infra red kit (sold separately)

The LINDY Fibre Optic HDMI Extender is the most cost effective, high performance solution on the market for sending HDMI signals over incredible distances. Using a standard SC duplex multimode (50/125µ) fibre optic cable (not included) to make the long distance connection, the HDMI Extender provides full support for HD 1080p, HDCP, multi channel audio, CEC and IR remote control.

Unlike other manufacturer's solutions, the LINDY Fibre Optic HDMI Extender uses just one duplex fibre cable - no additional Ethernet patch cables are required for DDC and remote control.

HD1080p, multi channel audio, HDCP, CEC and remote control over a single cable!

The extender system comprises two modules, a transmitter and a receiver, which are connected to both the HDMI source and display using standard of up to 3m. The modules are then connected together using a single, standard 'off the shelf' of up to 300m in length (fibre optic cable is not included)

Additional Requirements

• Fibre Optic Patch cable: (of required length up to 300m)
• Two HDMI cables for connecting to source and display: or (up to 3m in length)
• LINDY Infra red kit for using IR remote controls

Package Contents:

1 x Fibre Optic HDMI Transmitter Unit

1 x Fibre Optic HDMI Receiver Unit

2 x Multi Country 5V 2.6A Power Supplies

8 x Rubber Feet

LINDY Manual

• Extends DVI-D signals at distances of up to 300m using a single
• Compatible with DVI-D 2.0 specifications including HDCP 1.1 and HDTV and HD-Ready displays
• Supports HDTV resolutions up to 1920 x 1200 @ 60Hz / 1080p @ 60 Hz and 3D
• 6Gbps Total Bandwidth over Single 2-core Fibre Optic Cable Link
• IR Frequency range 35-45kHz
• 2 year warranty

*Remote control requires Infra-red kit

• Extends an IR remote control system when used with a Lindy Fibre Optic Extender
• Suitable for use with No. 38003/38004/38063/38163
• Supports IR frequencies 36 - 56kHz
• Cable Length: 1m (each unit)
• 2 Year Warranty

The IR Kit for Fibre Optic AV Extenders enables the extension of IR remote control signals alongside AV signals. The kit comprises of a Receiver and an Emitter which are then directly connected to the extender, and sited in a suitable location at either end of the installation using the adhesive pads on the base of each unit.

• Extend HDMI signals at distances of up to 700m using a single LC duplex single mode fibre cable
• For non HDCP protected signals distances of up to 3km are possible
• Supports resolutions up to 4K@60Hz 4:2:0 8bit
• HDCP 2.2/1.4 Pass-through ensuring maximum compatibility
• 2 year warranty

The Lindy Fibre Optic HDMI 4K30 Extender is a high performance solution for extending HDMI signals over incredible distances. Using a standard LC duplex single mode (9/125µ) fibre optic cable to make the long distance connection, this HDMI Extender provides support for 4K Ultra HD resolutions, ideal for attention grabbing digital signage, high end residential installations or an event’s AV distribution.

The extender system comprises two modules, a transmitter and a receiver, which are connected to both the HDMI source and display using standard HDMI cables of up to 5m. The modules are then connected together using a single, standard LC duplex single mode fibre cable of up to 700m (3km if without HDCP) in length (fibre optic cable is not included).

Support for IR extension can be added by purchasing the IR Extender Kit, which allows the control of IR equipment connected to the Transmitter from the remote Receiver.

• Full CAT6 specification with moulded boots

• Snagless strain relief prevents damage to the RJ-45 latch during installation and removal

• Standards: ISO/IEC 11801, EN50173, EIA/EIA 568B.2
• Gigabit Ethernet ready
• 100% performance tested
• Stranded core cables allowing repeated flexing without damage, prolonging the life of the cable
• Ideal for connecting computers, hubs, switches, print servers, patch panels, etc.
• Useful for Color coding your departments, workgroups, etc.
• 10 year warranty

• Extend DVI-D Dual Link signals up to 500m using a single fibre optic cable (not included)
• Compatible with DVI-D 2.0 specifications including HDTV & HD-Ready displays
• Supports HDTV resolutions up to 2560 x 1600 @ 60Hz / 1600p @ 60 Hz
• Auto & Self learning EDID transmission
• No HDCP support
• Auto laser cut off if fibre optic cable is broken or DVI-D cable removed
• 2 year warranty

Easy to set up and install this compact Fibre Optic DVI-D Dual Link Extender is a cost effective, high quality solution for sending DVI-D signals up to 500m without any compression or degradation over MPO Multimode cable.

Unlike other solutions, this extender uses just a single fibre cable to reach such great lengths. The system comprises of transmitter and receiver modules that connect directly to the digital source & display via DVI-D. The modules are then connected using a single, MPO fibre optic cable (not included).

Please note - We recommend using 50/125µ or 62.5/125µ MPO multimode fibre cable. Please contact Technical Support for further advice.

Package Contents

• 1 x Transmitter Unit
• 1 x Receiver Unit
• 2 x multi country 5V 1A power supplies
• LINDY Manual